Feb 16, 2008

120W DC/AC Inverter

1.0INPUT REQUIREMENT
  1.1Voltage input voltage 12V dc

Minimum
Nominal
Maximum
10.5Vdc
12Vdc
14.5Vdc

  1.2 Current
  The maximum input current is 13A at 10.5V dc.
  1.3 Power saving
  No load consumption Input under 3 W at 12V dc.
2.0 OUTPUT REQUIREMENT
  2.1 Output Voltage:110V±10%
  2.2 Output Current:0-1A
  2.3 Output Voltage Frequency:60Hz±2
  2.4 Output Voltage Waveform: Square wave
  2.5 Peak Efficiency:>90%
3.0PROTECTION REQUIREMENT
  3.1 Low Input Voltage protection: 9.7V-10.2V
  3.2 High Input Voltage protection: 14.7V-15.2V
  3.3 AC output short circuit protection: YES
4.0ENVIRONMENTAL CONDITIION
  4.1 Operating
  The Invertor shall be capable of operating continuously in any mode without performance deterioration in the following environmental conditions.
  4.1.1 Ambient Temperature: 0~40
  4.1.2 Relative Humidity: 20%~85%
 

Feb 11, 2008

Outsouce Power Cords from Taiwan, China, Pacrim

telCade Presents:

Power cord

From Wikipedia, the free encyclopedia

power cordline cord, or mains cable is a cord or cable that temporarily connects an electrical appliance to the distribution circuits of an electrical power source via a wall socket or extension cord.

The terms are generally used for cables using a power plug to connect to a single-phasealternating current power source at the local line voltage—generally 100 to 240 volts, depending on the location). The terms power cablemains lead or flex are also used. Alamp cord is a light weight ungrounded two wire cord used for small loads such as a table or floor lamp. The term cord set is also used to distinguish those cords that include connectors molded to the cord at each end.[1]

Power cables may be either fixed or detachable from the appliance. In the case of detachable leads, the appliance end of the power cord has a socket (female connector) rather than a plug (male connector) to link it to the appliance, to avoid the dangers from having a live protruding pin. Cords may also have twist-locking features, or other attachments to prevent accidental disconnection at one or both ends. A cord set may include accessories such as fuses for overcurrent protection, a pilot lamp to indicate voltage is present, or aleakage current detector. Power cords for sensitive instruments, or audio/video equipment may also include a shield over the power conductors to minimize electromagnetic interference.

Contents

 

Connectors

Common types of detachable power cable have appliance-side connectors such as the IEC 60320 C13 sometimes colloquially known as an IEC connector, "kettle lead", "jug plug" or "IBM plug" (commonly used for higher current appliances where an earth or ground connection is required) and IEC 60320 C7 commonly used for low-current applications such as an power supply inlet for use with a laptop computer. The IEC C7 is also known as a "figure-of-eight lead" (connecting by two small round pins, with round insulating bushings; the connector has a figure-of-eight cross section). The polarised IEC 60320 C5 connector is now commonly used on the AC side of laptop computer power supplies. The IEC C5 is commonly known as "cloverleaf plug" or "Mickey Mouse plug" because of the shape of its cross section.

IEC power cables come in high-temperature and low-temperature variants, as well as various current capacities. The connectors have slightly different shapes to ensure that it is not possible to substitute a cable with a lower temperature or current rating, but that it is possible to use an over-rated cable. Cords also have different types of exterior jackets available to accommodate environmental variables such as moisture, temperature, oils, sunlight, flexibility, and heavy wear. For example, a heating appliance may come with a cord designed to withstand accidental contact with heated surfaces.

World-wide, more than a dozen different types of connectors are used for fixed building wiring. Products sold in many different markets can use a standardized IEC connector and then use a detachable power cord to match the local electrical outlets. This simplifies safety approvals, factory testing, and production since the power cord is a low-cost item available as a commodity. Note that the same types of appliance-side connectors are used with both 110 V and 230 V power cables, so care must be used when moving appliances between countries with different voltage standards — substituting a power cord that matches local power outlets will result in an incorrect voltage being applied to the appliance or equipment. Some devices have a slide-switch to adapt to different voltages, or wide-ranging power supplies. Unless explicitly labelled as capable of handling local voltages, this is very likely to damage or destroy the appliance.

Power supplies

Cord sets must be distinguished from plug-in wall mounted power supplies, where the connector also contains a transformer, and possibly rectifiers, filters and regulators. Unwary substitution of a standard mains-voltage connector for the power supply would result in application of full line voltage to the connected device, resulting in its destruction and possible fire or personal injury.

See also


Contact Us

Your partner to source custom parts. Contact telCade.

Cable Keywords Research

Adapters
Audio Video Cables
Audio Video Devices
Bulk Cable
Cat5e, Cat6 Cables
CATV and SATV
Connectors
DVI
Fiber Cables
Gender Changers
HDMI
Home Distribution
iPod®/FireWire®
KVMs & Switches
Monitor Cables
Network Cable/Devices
PC Cables
Power Cords & Chargers
RapidRun™ A/V
SCSI
Tools & Testers
USB
VGA
Wall Plates & Premise Wiring

What is ISO TS16949 Certification Standard?

ISO/TS 16949:2002 specifies the highest quality standard. The automotive industry is the first industry to adopt it under one global quality system standard. ISO TS16949incorporates ALL the requirements of ISO 9001:2000 PLUS an additional 130 requirements. It also includes many of the elements of QS9000 PLUS many new requirements for metrics to measure business processes and continuous improvement.

ISO/TS 16949 requires companies to monitor all their production and engineering processes. The average company must increase the number of processes it monitors from a few dozen to more than 150.


All manufactured cable assemblies and wiring harnesses are 100% tested to your specifications.
Electronic Programmable Testing
Visual Inspection
Documented Quality Procedures
Date Code and Lot Number Protection
First Piece Approvals
Revision Compliance
Certificate of Compliance
Incoming Parts Verification and Inspection

We manufacture custom, standard, molded cable assemblies and wiring harnesses to include, but not limited to: 
Communications
Medical
Robotics
Industrial Equipment
Gaming
Transportation
Computer
Utility
Automation
Power Management
Contract Management
Defense
Aerospace
Turnkey Projects
Value Added Services
Environmental


Analog and Digital cable assemblies
Audio and Video cable assemblies
Black Box applications
Coaxial cable assemblies
Coil cord assemblies
Custom cable assemblies
DIN and Mini DIN connector assemblies
Discrete wire harnesses
Fan wiring assemblies
Ferrite bead cable assemblies
Contract Kitting and Testing
Electronic assemblies and sub-assemblies
Electro-Mechanical assemblies
Transportation industry wire harnesses
Military defense wire harnesses and cables
Micro-miniature connector assemblies
Medical wiring assemblies
Molded cable assemblies
Power Distribution cabling
Ribbon cable assemblies
Robotic cable assemblies
Turn-Key applications
USB cable assemblies
Value-added assemblies
Plenum cable assemblies
Industrial equipment wiring assemblies
Power Cord assemblies
Firewire Cables
Network and Communication cables

Please see below some of the products we cover:

     Specialty Cable Harnesses: Medical / Hospital Grade, Industrial, Instrumentation, Sensors, Embedded Electronics, Insert molding
     Audio/Video, Projector and Multimedia Wire Harness
     Computer Cable Harness
      Car Stereo Wire Harness 
     Engine Cable Harness Wire 
     Radio Cable Harness 
      Motorcycle Stereo Wire Harness 
      Auto Wire Harness 
     Car Alarm Cable Harness 
      Car Cable Harness 
     Trailer Wire Harness 
     Automotive Wire Harness 
     Headlight Wire Harness 
     Off Road Equipment Wire Harness 
     Car Audio Cable Harness  
     Motorcycle Cable Harness
     Custom Cable Harness Assembly


We are the One Stop Shop for Cable Design, Cable Engineering, Cable Assembly Manufacturing and Injection Molding Services

Custom Computer Cables
Custom Network Cables
Custom Medical Cables
Custom Lead Wires
Custom Instrumentation Cables
Custom Lab Cables


Custom Audio Cables
Custom Video Cables
Custom Cables for Robotics
Custom Power Cables
Custom Electrical/ Industrial Cables
Custom Cable Harnesses


telCade supports all three major steps in developing a new harness:

  • Conceptual configuration to determine the relative dimensions needed. Our expertise in wiring layout and molding configuration helps to ensure a design that not only performs well but also improves your assembly process.

  • Pre-production, Samples and Proof of Design of the final design to be used in manufacturing. This is an actual piece that will be used in production, to confirm testing and layout requirements. This includes PPAP runs.

  • Manufacturing test-run of 50-100 units to support limited testing prior to full-scale production. This pre-production run is vital to insuring that quality standards are met at your anticipated production levels.

Short Run Factory Supports Quick Turnaround. Our underlying goal is speed in helping you move your design into production as quickly as possible, while identifying efficiencies that will benefit you in the long run.


  • Custom wire harnesses
  • Medical cables
  • Flat cables
  • Industrial harnesses
  • Electro-mechanical harnesses
  • Security system wire harnesses
  • Electrical wire harnesses



    Face Plates
    Panel-Mount Cables
    USB & FireWire
    Video Cables
    Video Electronics
    Keyboard & Mouse
    Networking
    Fiber Optic
    Wireless Products
    SCSI
    Serial & Parallel
    Manual Data Switches
    Data Interface Cables
    Audio Cables
    Power Cables
    Server Racks

Feb 1, 2008

6W 038Series AC/DC switching power adaptor


ELECTRICAL SPECIFICATIONS:
Input
   Input voltage: 100~240Vac
   Input Frequency: 50Hz~60Hz
   Input inrush current: 20A at 115Vac, 40A at 230Vac
Output
   Output voltage: 5V~12VDC
   Efficiency: 67% Normal at full load
   Ripple: 1% Peak to Peak
Protection
    Over Voltage Protection
    Short circuit Protection
Temperature
    Storage Temperature:-20 to+85℃
    Operating Temperature:0 to+40℃
Safety Certify
    CE、UL/CUL、TUV/GS、CB、PSE、EK-mark、CCC、BSMI、SAA、
    Citck、BS、FCC、China ROHS、CEC
Dimension
   57mmx41mmx33mm(length/width/height)
Customer Selection Guide
  (Model NO. XXX、XXX、XXXX、Z as this:Output power、Output Voltage、
     Output Current、Plug)
    Plug:  0 - JU:USA  1 – AU:Austrialia  2 – UK:England  3 – KE:Korea
             4 – PSE:Japan  5 – 3C:China  6 – EU:Europe
 
6W系列(Model Selection Table:(Single Output))
Model No.
Output Voltage
Output Current
Maximun Output
LY-SPA060-0500300Z
300mA
DC 5.0V±5%
1.5W
LY-SPA060-0500500Z
500mA
DC 5.0V±5%
2.5W
LY-SPA060-0500600Z
600mA
DC 5.0V±5%
3.0W
LY-SPA060-0500800Z
800mA
DC 5.0V±5%
4.0W
LY-SPA060-0501000Z
1000mA
DC 5.0V±5%
5.0W
LY-SPA060-0501200Z
1200mA
DC 5.0V±5%
6.0W
LY-SPA060-0550300Z
300mA
DC 5.5V±5%
1.65W
LY-SPA060-0550600Z
600mA
DC 5.5V±5%
3.3W
LY-SPA060-0550800Z
800mA
DC 5.5V±5%
4.4W
LY-SPA060-0551000Z
1000mA
DC 5.5V±5%
5.5W
LY-SPA060-0600300Z
300mA
DC 6.0V±5%
1.8W
LY-SPA060-0600600Z
600mA
DC 6.0V±5%
3.6W
LY-SPA060-0600800Z
800mA
DC 6.0V±5%
4.8W
LY-SPA060-0601000Z
1000mA
DC 6.0V±5%
6.0W
LY-SPA060-0750300Z
300mA
DC 7.5V±5%
2.25W
LY-SPA060-0750600Z
600mA
DC 7.5V±5%
4.5W
LY-SPA060-0750800Z
800mA
DC 7.5V±5%
6.0W
LY-SPA060-0900300Z
300mA
DC 9.0V±5%
2.7W
LY-SPA060-0900500Z
500mA
DC 9.0V±5%
4.5W
LY-SPA060-0900700Z
650mA
DC 9.0V±5%
5.85W
LY-SPA060-1200250Z
250mA
DC 12.0V±5%
3.0W
LY-SPA060-1200300Z
300mA
DC 12.0V±5%
3.6W
LY-SPA060-1200500Z
500mA
DC 12.0V±5%
6.0W
 

203W AC/DC switching power adaptor


ELECTRICAL SPECIFICATIONS:
Input
  Input voltage: AC100~240Vac
  Input Frequency: 50Hz~60Hz
  Input inrush current: 20A at 115Vac, 40A at 230Vac
Output
  Output voltage: double Output 5VDC/1A & 12VDC/16.5A
  Efficiency: 80% Normal at full load
  Ripple: 1% Peak to Peak
Protection
  Over Voltage Protection
  Short circuit Protection
Temperature
  Storage Temperature:-20 to+85℃
  Operating Temperature:0 to+40℃
Safety Certify
  CE、UL/CUL、TUV/GS、CB、PSE、EK-mark、CCC、BSMI、SAA、
  Citck、BS、FCC、China ROHS、CEC
Dimension
  160mmx95mmx45mm(length/width/height)
Customer Selection Guide
  (Model NO. XXX、XXX、XXXX、Z as this:Output power、Output Voltage、
    Output Current、Plug)
    Plug:  0 - JU:USA       1 – AU:Austrialia  2 – UK:England  3 – KE:Korea
            4 – PSE:Japan  5 – 3C:China       6 – EU:Europe
 
203W&120W(Model Selection Table:( double Output))
Model No.
Output Voltage
Output Current
Maximun Output
LY-SPA203-1201650Z
16.5A*1.0A
DC:12±5% *5V±5%
203W
LY-SPA203-2408250Z
8.25A*1.0A
DC:24±5% *5V±5%
203W
LY-SPA203-3605500Z
5.5A*1.0A
DC:36±5% *5V±5%
203W
LY-SPA120-1209600Z
9.6A*9.6A
DC:12±5% *5V±5%
120W
LY-SPA120-2404800Z
4.8A*9.6A
DC:24±5% *5V±5%
120W
LY-SPA120-3603200Z
3.2A*9.6A
DC:36±5% *5V±5%
120W

 

24W Series AC/DC switching power adaptor


ELECTRICAL SPECIFICATIONS:
Input
  Input voltage: 100~240Vac
  Input Frequency: 50Hz~60Hz
  Input inrush current: 20A at 115Vac, 40A at 230Vac
Output
  Output voltage: 5V~24VDC
  Efficiency: 76% Normal at full load
  Ripple: 1% Peak to Peak
Protection
  Over Voltage Protection
  Short circuit Protection
Temperature
  Storage Temperature:-20 to+85℃
  Operating Temperature:0 to+40℃
Safety Certify
  CE、UL/CUL、TUV/GS、CB、PSE、EK-mark、CCC、BSMI、SAA、
  Citck、BS、FCC、China ROHS、CEC
Dimension
  73mmx35mmx61mm(length/width/height)
Customer Selection Guide
  (Model NO. XXX、XXX、XXXX、Z as this:Output power、Output Voltage、
    Output Current、Plug)
    Plug:  0 - JU:USA  1 – AU:Austrialia  2 – UK:England  3 – KE:Korea
             4 – PSE:Japan  5 – 3C:China  6 – EU:Europe
 
24W系列(Model Selection Table:(Single Output))
Model No.
Output Voltage
Output Current
Maximun Output
LY-SPA240-0501500Z
1500mA
DC 5.0V±5%
7.5W
LY-SPA240-0502000Z
2000mA
DC 5.0V±5%
10.0W
LY-SPA240-0502600Z
2600mA
DC 5.0V±5%
13.0W
LY-SPA240-0503000Z
3000mA
DC 5.0V±5%
15.0W
LY-SPA240-0503800Z
3800mA
DC 5.0V±5%
19.0W
LY-SPA240-0751000Z
1000mA
DC 7.5V±5%
7.5W
LY-SPA240-0751500Z
1500mA
DC 7.5V±5%
11.25W
LY-SPA240-0752000Z
2000mA
DC 7.5V±5%
15.0W
LY-SPA240-0752500Z
2500mA
DC 7.5V±5%
18.75W
LY-SPA240-0753000Z
3000mA
DC 7.5V±5%
22.5W
LY-SPA240-0901000Z
1000mA
DC 9.0V±5%
9.0W
LY-SPA240-0901500Z
1500mA
DC 9.0V±5%
13.5W
LY-SPA240-0902000Z
2000mA
DC 9.0V±5%
18.0W
LY-SPA240-0902500Z
2500mA
DC 9.0V±5%
22.5W
LY-SPA240-1200750Z
750mA
DC 12.0V±5%
9.0W
LY-SPA240-1201000Z
1000mA
DC 12.0V±5%
12.0W
LY-SPA240-1201500Z
1500mA
DC 12.0V±5%
18.0W
LY-SPA240-1202000Z
2000mA
DC 12.0V±5%
24.0W
LY-SPA240-1381000Z
1000mA
DC 13.8V±5%
13.8W
LY-SPA240-1381500Z
1500mA
DC 13.8V±5%
20.7W
LY-SPA240-2400500Z
500mA
DC 24.0V±5%
12.0W
LY-SPA240-2400750Z
750mA
DC 24.0V±5%
18.0W
LY-SPA240-0501500Z
1500mA
DC 5.0V±5%
7.5W